The article following next pertaining to A Step-by-Step Guide to Installing a Bathtub is absolutely entertaining. Don't bypass it.
Setting up a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the new one. See to it you have certified on your own for the job as well as are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will certainly aid you install a new tub in your bathroom if you have already acquired a brand-new tub as well as do not require to transform the arrangement of your previous supply of water pipelines.
Your devices and also product checklist ought to make up the following:
Getting ready for the Setup
First of all, the sustaining frame provided with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the limited access that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the called for setting. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bath tub up until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if required. Load the bathtub and additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former type ought to be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break an inflexible seal, creating the water to pass through the wall surface between the bath as well as the tiling, causing problems with moisture and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can fracture relatively early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article about Installing A Bathtub through an associate on our other web page. Are you aware of another individual who is involved in How to Install a Bathtub Yourself? Be sure promote it. Thanks for going through it.
Request Estimate